Today I am sharing a project I started over a month ago. The entire thing took me about 30 minutes to finish, but I somehow managed to take a month to get the darn thing photographed. I blame a crazy summer with 5 kiddos
We have some blank space on the wall by our front door. I thought it would be so fun to create something fun to fill that space and serve a little function at the same time! Check out my DIY Address Number Wall Planter…
How cute is that? This thing is SO simple to make, and you can hang it with 3M fastening tape making it a perfect project for those of you who rent your home as well!
Let’s get started!
1 – 5.5″ cedar fence picket (mine is 3/4″ thick… if you use 5/8″ be sure to adjust your pocket holes)
1 x 4 x 8 cedar board – you will have scrap, but that’s she shortest you can buy at Home Depot
Metal Address Numbers
plants – I used succulents from Home Depot
With the plants included, the entire project cost me under $25. You can use less expensive plants, but you will have to water them more which I fail at.
Start by making your cuts! I cut my fence picket into 3 pieces that were each 18″ long. I used my Ridgid miter saw for this part (which I love dearly and is always on my favorite tools list) but you can also use a small hand saw like this one.
I used my Kreg Jig to add 3/4″ pocket holes on two of those 3 boards I just cut. I love my new K5
model, but I mounted my K4
to a board and I keep it handy to pull out when I have really long boards that won’t fit on top of my workbench. Both models are amazing, but my fav is for sure the K5 with all of the cool updates.
At this point, your boards should look a bit like this…
I used my Ryobi 18V One+ drill to attach my boards using 1 1/4″ pocket hole screws through my pocket holes.
1 – 10.5″
2 – 3.5″
1 – 12″
I added 3/4″ pocket holes to one side of the 10.5″ piece. I use these pocket holes to attach the planter to the planked back. These will face up and will be covered by the plants. After adding those pocket holes, I attached my two 3.5″ side pieces to the 10.5″ bottom piece using Gorilla wood glue and 1.25″ brad nails.
Next, I attached this piece to my planked back using wood glue and 1.25″ pocket hole screws through those pocket holes I mentioned earlier. I didn’t measure this part at all… Just used the old eyeball method.
My final step was attaching the top 12″ board. I used my Ryobi Airstrike Brad Nailer with 1.25″ brad nails and wood glue to attach it.
I chose to use Varathane Stain from Home Depot in the color Carrington. It’s one of our very fav colors. I think it’s the richest brown I have found, and it dries in under an hour and only requires one coat. That makes it even prettier
Once the stain dried, I used my Ryobi Corner Cat sander to distress all of my edges and corners. This is my very FAV sanding tool out there. It’s lightweight and super powerful and uses the same battery as my drill. The tool by itself is only $29 which is an amazing price! I use it on every project I do.
This step is totally optional! I just love the rustic ‘shanty’ look it gives the whole piece!
After that dried, I attached my numbers. I found mine at Home Depot.
I found the succulents at Home Depot as well. I filled my planter with a few and hung it on the wall. I used 3M heavy duty mounting tape to hold mine. It has now been hanging steady for about a week. You may choose to hang yours differently depending on where you are putting it! Here are a few more shots…
Thanks so much for stopping by! Wouldn’t this make a great hostess or housewarming gift?? I love the little touch it adds to our entry. I also love that it took me 30 minutes to throw together…. My kind of project people! Let me know if you have any questions at all! I would LOVE for you to share and PIN this project with all of your friends.
Thanks so much for stopping by!
Original article and pictures take http://www.shanty-2-chic.com/2014/07/diy-address-number-wall-planter.html site