Wowwwwww! How fun was that?!?!? Thank you to everyone who just tuned in to our two new episodes of Open Concept on HGTV! We decided that the first plan (of many more to come) to share with you guys should be the Modern Farmhouse Table that we built for the Berry House! We have had so many requests for the plans, since we did built it live on Facebook, so of course, we can’t make y’all wait any longer for it! If you missed the live build you can see it HERE on our Facebook page.
Now for the build! This is an easy build with minimal steps – yay! If you are a newbie to building, this is a good table to tackle!
Here are the 5 tools you need to build it:
You can click the image above or HERE to print the free plans!
I started with 4 of these furniture legs from Osborne. I used knotty pine and you can find them here! If you want to save money and have the tools, you can piece together scrap 2×4 boards to form a 5’x5′ leg.
To begin, I ripped the rounded edges off of every board. This is necessary for the planks on the table top because you want them to be 5″ – the exact width of the table legs. It’s also great to do this because it will create a smooth table top and you won’t have “crumb catchers” between each board. We also did this to the 2×3 apron pieces and supports because it gives a more high-end look (and it’s modern so the clean lines add to that style).
Make the cuts for the apron pieces first. Then drill two, 1 1/2″ pocket hole screws into the ends of each piece. You can find the Kreg Jig K5 on Amazon HERE. You can see our tutorial video, How to Use a Kreg Jig HERE!
Now, attach the apron pieces to the legs. You will put each piece 1 1/2″ down from the top of the table leg. This will give room for the planks on the top and allow the top of the legs to show. The apron piece is also centered on the leg.
Next, cut the cross supports and drill six, 1 1/2″ pocket holes into each board. You want these to fall around the center of each plank so, mark in 4 1/4″ from one end for the first pocket hole. Then, make one every 5 inches after that. You will see the holes on the top of the board but that’s ok! You won’t see them under the table You will also put two 1 1/2″ pocket holes on each end of the supports.
Now for the top! Cut your outside planks first. Then, drill two 1 1/2 pocket holes on each end of the boards. Make sure the pocket holes are close to the edges of the board because the apron will rest between them.
Now for the stain!
I mixed Varathane Ash and Varathane weathered gray stain – 50:50 ratio. To apply the stain, just wipe it on with a clean cloth, let it dry for about 5 minutes then wipe the stain with another clean cloth.
Ready for the finish
To protect the surface, I applied one coat of Varathane Triple Thick Polyurethane in satin finish. Use a paint brush to apply.
That was IT! How easy is that?! If you want to find the other things you see in the this space you can click the links below!
Dining Chairs from Wayfair HERE
Chandelier from West Elm HERE
The mirrors on the wall can be found HERE
Hanging Basket on Wall from World Market HERE
Napkins from Anthropologie HERE
Napkin Rings from World Market HERE
White Dinner Plates from Target HERE
Round Salad Plate from Target HERE
Table Runner from World Market HERE
Woven Chargers from Hobby Lobby
Thank you so much, again, for tuning in to our show! If you missed it, we will keep you posted as soon as we find out when it will re-air!
Thank you guys!
Ashley and Whitney
Original article and pictures take http://www.shanty-2-chic.com/2016/06/diy-modern-farmhouse-table-seen-hgtv-open-concept.html site