Installing a pair of pre-hung French doors and a DIY transom completely transformed not just one, but two rooms in Elisha Albretsen’s home.
Elisha, who writes the blog Pneumatic Addict, is a fearless DIYer, and shows us exactly how she and her husband completed this project.
Installing the French Doors
We sold our home last year and started house hunting. We were looking for a 4-bedroom home, but when we came across a “3-bedroom plus den” with the perfect floor plan in the perfect location, we changed our minds and rolled up our sleeves.
Our “den” was just a small room, open directly into the living room. I have plans to turn this space into a playroom for my boys, but in the meantime it was no man’s land and a landing place for random junk. Not a pretty view for our guests.
Right away we made plans to install a pair of French doors. However, we had a dilemma. The existing opening to the den was 8 feet tall. My front door is 8 feet tall as well, but the rest of the doors in my home are the standard 6 ft. x 8 in. height.
The debate was “Should I hang 8 ft. tall doors to fill the space? Or go with shorter doors and match the rest of the house?”
We headed to The Home Depot and picked up a pair of 60 in. x 80 in. French doors.
The first step we took was to prep the opening for the doors. The French doors we used required a 62 in. rough opening. For us, that meant removing the drywall and moving one of the trim studs.
Building the Transom Window
With the doors in place, I started building the transom window.
I used 4-9/16 in. wide door jamb stock, which I found in the moulding aisle. To determine the size the window needed to be, I measured the rough opening above the doors.
I purposely made the window ¼ in. smaller, both in width and height so I could use shims and make sure it was level and plumb.
Next, I divided the interior length by three, giving me three equally sized windows.
Then, I attached the dividers with more glue and finish nails.
I measured the circumference of each window opening.
Then, I cut and mitered the trim, creating a frame.
Installing the Transom Window
At this point, the transom was ready to install above the doors. I slid the window in the opening, shimmed it in place and secured it with more 16-gauge nails.
With the doors and windows installed, I could add the door casing and decorative trim. I attached a small strip of lattice moulding over the seam between the doors and window, making the two look like one united piece.
Next, I caulked every seam and filled all the nail holes with wood filler. I painted the casing to match the rest of the trim in my home and painted the door and transom, using the color “Raven Black” by Behr, in a satin sheen.
Cutting glass isn’t nearly as scary as it sounds. I cut my own glass for my kitchen remodel, but since the transom is within 24 in. of an active door, residential building code requires the window glass to be tempered. I ordered three pieces of ⅛ in.-thick tempered glass from a local glass company for around $75.
In each window section, I ran a bead of clear silicone caulk on the flat side of the quarter round trim and pressed a sheet of glass firmly in place.
Using 18-gauge brads, I very carefully attached the moulding to the transom frame, sandwiching the glass and holding it in place.
The hinges included with my set of doors were Satin Nickel, which worked perfectly with the black doors, so I chose Kwikset Milan levers in the same color.
That means I didn’t have to worry about drilling out and attaching a lock bolt to hold one side closed. Both doors can be opened or closed independently. More importantly, I could use dummy levers instead of a functioning door knob.
A dummy lever is fixed in place and doesn’t use a bolt and strike plate. Since the ball catch holds the door closed, I just needed something to grab when I push or pull the door.
I attached a dummy lever on both sides of each door.
Lastly, I screwed the ball catch strike plates to the top jamb, making sure they lined up properly with the bearings in the doors.
I’ll admit, I was super nervous about painting the doors, transom and whole jamb black, but I’m so glad I did! I love the contrast between the dark door and my white walls.
Although it looks intimidating, my transom window was really pretty simple to build. Its basically a box with sheets of glass held in place with quarter-round moulding.
Original article and pictures take http://blog.homedepot.com/installing-french-doors-diy-transom-window/ site